GOOGLEに接続できません

I18n Error: Missing interpolation value "x" for "投稿者 |@plgn|{{ x }} |plgn@| on |@plgn|{{ x }} |plgn@|"

こんにちは、私のスプロケットはグーグルに接続できません。それはただ回転し続けます。他のソーシャルメディアアカウントは正常に機能しています。アプリを再インストールしようとしました...まだ機能していません。


古い投稿 新しい投稿

I18n Error: Missing interpolation value "x" for "|@plgn|{{ x }} |plgn@| コメント"

  • Tried everything u mentioned…give up…not able to connect…

    I18n Error: Missing interpolation value "x" for "|@plgn|{{ x }} |plgn@| on |@plgn|{{ x }} |plgn@|"
  • Hi! @adamte0, Thank you for visiting the HP Forums! A great place where you can find solutions for your issues with help from the community!
     
    I understand you have issues connecting to Google using HP sprocket app.
     
    Don’t worry I’ll try to help you out.
     
    Did you make any changes to your printer?
     
    Have you signed into your google account?
     
    Are you using an android or an IOS device?
     
    Please try few steps recommended below.
     
    1.    Reset the Sprocket unit by placing a push-pin or needle into the small hole on the rear of the unit.  (Reset instructions in the support doc HERE)
    2.    Plug in the Sprocket unit with the provided micro-USB cable.  Connect to either a computer USB port or USB wall charger.
    3.    Allow the Sprocket unit to charge for 10 minutes.  Note:  A call back may be required in these instances.
    4.    Power on the Sprocket unit by pressing/holding the power button for 3 seconds.
    5.    A white LED should illuminate on the rear of the unit if the power-up is successful.
    6.    Remind the customer to charge their Sprocket for an additional 60-90 minutes to enable a full battery charge.
     
    Also, try the steps recommended below.
     
    Turn on the printer. By default, the printer is set to turn off after 5 minutes. To change when the printer automatically
    turns off, open the HP Sprocket app on your mobile device. Tap , tap sprocket, and then tap Auto Off. Select when
    you want the printer to turn off.
    • Restart your mobile device. Turning off and then turning on your mobile device might clear any errors.
    • Check for an HP Sprocket app update. On your mobile device, go to the Google Play Store™ or the App Store®, and then
    search for the HP Sprocket app. Select the app from the list, and then check for an update.
    • Update the printer firmware. On your mobile device, make sure it is connected to the Internet, and then open the HP
    Sprocket app. If there is a firmware update available, a firmware update screen displays. Follow the on-screen prompts
    to complete the update.
    Troubleshooting and FAQs
    13
    • Update the software on your mobile device. Check your mobile device settings to confirm you have the latest version
    of the operating system software installed. Contact your mobile phone manufacturer for more information about
    updating the operating system.
     
    If the issue still persists try updating the sprocket firmware from the sprocket app and check if it helps.
     
    Open Sprocket app go to menu—>Sprocket—→ Printers; A blue firmware update link will be present if an update is available.
     
    Refer this article to further troubleshoot HP sprocket app issues. Link: http://bit.ly/2tqndBa
     
    If the solution provided worked for you, please mark accepted solution for this post.
     
    Hope to hear from you soon!
    Have a great day! 🙂
     
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
                                                                                                                                   
    Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

    A4Apollo I am an HP Employee
    I18n Error: Missing interpolation value "x" for "|@plgn|{{ x }} |plgn@| on |@plgn|{{ x }} |plgn@|"


コメントを残す