充電中はライトが点滅

I18n Error: Missing interpolation value "x" for "投稿者 |@plgn|{{ x }} |plgn@| on |@plgn|{{ x }} |plgn@|"

私は昨日スプロケットを持ってきて3時間以上充電させただけで、死ぬ前に3枚の写真を印刷することができました。私はそれを再充電して脇に置き、今朝それを試して使用すると電源が入ることさえありました。今日、スプロケットを充電に差し込んだとき、LEDライトが赤と緑に同時に点滅し、コードを取り出すとすぐに消えます。アプリによると、スプロケットを接続すると、バッテリーが100%あると表示されます。私はとても混乱していてイライラしています誰か助けてください

古い投稿 新しい投稿

I18n Error: Missing interpolation value "x" for "|@plgn|{{ x }} |plgn@| コメント"

  • Thanks for the reply and trying the suggested steps, the issue you are facing seems to be a hardware issue, recommend you contact our phone support for the service options available. 
     
    Keep me posted. Good Luck. 

    Chimney_83 I am an HP Employee
    I18n Error: Missing interpolation value "x" for "|@plgn|{{ x }} |plgn@| on |@plgn|{{ x }} |plgn@|"
  • Hi, thanks for getting back to me. Unfortunately I have done the things you recommended and the light is still flashing red and green and it will not hold charge.

    I18n Error: Missing interpolation value "x" for "|@plgn|{{ x }} |plgn@| on |@plgn|{{ x }} |plgn@|"
  • Hi! @Brooke4793, Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community! I understand when you plug the sprocket to charge LED light is flashing red and green. Don’t worry I’ll try to help you out. Did you make any changes to your printer? Try the steps recommended below. Please try few steps recommended below. 1.    Reset the Sprocket unit by placing a push-pin or needle into the small hole on the rear of the unit.  (Reset instructions in the support doc HERE)
    2.    Plug in the Sprocket unit with the provided micro-USB cable.  Connect to either a computer USB port or USB wall charger.
    3.    Allow the Sprocket unit to charge for 10 minutes.  Note:  A call back may be required in these instances.
    4.    Power on the Sprocket unit by pressing/holding the power button for 3 seconds.
    5.    A white LED should illuminate on the rear of the unit if power up is successful.
    6.    Remind the customer to charge their Sprocket for an additional 60-90 minutes to enable a full battery charge.
      If the issue still persists uninstall the sprocket app and reinstall the app and try updating the sprocket firmware from the sprocket app and check if it helps. Open Sprocket app go to menu—>Sprocket—→ Printers; A blue firmware update link will be present if an update is available. Refer this article to know more information about using sprocket printer. Also, refer the printer user guide for more information. If the issue persists after trying out the steps, please contact HP support for service options. Link to contact HP.  Let me know if this helps!Have a pleasant day ahead! 🙂  Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.                                                                                                                  Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

    A4Apollo I am an HP Employee
    I18n Error: Missing interpolation value "x" for "|@plgn|{{ x }} |plgn@| on |@plgn|{{ x }} |plgn@|"

コメントを残す