Impression de pignon de mauvaise qualité

Publié par Beth941 le

C'est mon deuxième pignon et il garde une qualité d'impression horrible. Le premier m'a donné des teintes roses et rien ne l'a réparé, alors j'ai eu un remplacement. Le premier paquet d'impressions était bien mais maintenant c'est une qualité horrible très floue et pixélisée. J'ai suivi chaque étape donnée sur d'autres forums pour essayer de le réparer et rien ne fonctionne. J'ai mis à jour le firmware, nettoyé les rouleaux, mis à jour l'application, réinitialisé l'imprimante, utilisé uniquement du papier HP zinc, littéralement tout et c'est horrible. Que puis-je faire d'autre car il s'agit maintenant de la deuxième imprimante qui n'imprime pas selon la norme que vous préconisez ? ? Je suis presque sur le point d'obtenir un remboursement complet car c'est tellement frustrant

 

 

← Article plus ancien Message plus récent →

5 commentaires

  • Hi, my sprocket 200 has suddenly started printing my photos dark and bad quality. I don’t know how to fix it and I’ve tried some things you’ve suggested. The pictures come out blueish and poor print quality. I am really upset about this. What is the problem and how am I supposed to fix it? Thank you so much 😊 Evangelina

    Evangelina le

  • Hi! @Beth941,
     
    This situation will need some additional support from our internal teams in HP. For that to happen, we will give you additional instructions/information via PM. 
     
     
    Regards
    Mr.Robot
     

    A4Apollo I am an HP Employee
    A4Apollo le

  • Thankyou for the response but as I mentioned, I have tried every single option available including everything you have mentioned and it still prints horribly. Its clearly a fault as this is a replacement and is still printing bad quality. Is there anything else can I do besides getting a refund? 

    Beth941 le

  • Hi! @Beth941, Thank you for visiting the HP Support Community! A great place where you can find solutions for your issues with help from the community!
     
    Don’t worry I’ll try to help you out.
     
    Did you make any changes to the printer?
     
    Please share the image you are running on the device to assist you better.
     
    Excellent description and a great diagnosis done. It is greatly appreciated.
     
    Let’s continue with the troubleshooting now.
     
    1.    Reset the Sprocket unit by placing a push-pin or needle into the small hole on the rear of the unit.  (Reset instructions in the support doc HERE)
    2.    Plug in the Sprocket unit with the provided micro-USB cable.  Connect to either a computer USB port or USB wall charger.
    3.    Allow the Sprocket unit to charge for 10 minutes.  Note:  A call back may be required in these instances.
    4.    Power on the Sprocket unit by pressing/holding the power button for 3 seconds.
    5.    A white LED should illuminate on the rear of the unit if the power-up is successful.
    6.    Remind the customer to charge their Sprocket for an additional 60-90 minutes to enable a full battery charge.
     
    Also, try the steps recommended below.
     
    Turn on the printer. By default, the printer is set to turn off after 5 minutes. To change when the printer automatically
    turns off, open the HP Sprocket app on your mobile device. Tap , tap sprocket, and then tap Auto Off. Select when
    you want the printer to turn off.
    • Restart your mobile device. Turning off and then turning on your mobile device might clear any errors.
    • Check for an HP Sprocket app update. On your mobile device, go to the Google Play Store™ or the App Store®, and then
    search for the HP Sprocket app. Select the app from the list, and then check for an update.
    • Update the printer firmware. On your mobile device, make sure it is connected to the Internet, and then open the HP
    Sprocket app. If there is a firmware update available, a firmware update screen displays. Follow the on-screen prompts
    to complete the update.
     
    Troubleshooting and FAQs

    • Update the software on your mobile device. Check your mobile device settings to confirm you have the latest version
    of the operating system software installed. Contact your mobile phone manufacturer for more information about
    updating the operating system.
     
    If the issue still persists try updating the sprocket firmware from the sprocket app and check if it helps.
     
    Open Sprocket app go to menu—>Sprocket—→ Printers; A blue firmware update link will be present if an update is available.
     
    Refer this article to further troubleshoot HP sprocket app issues. Click Here 
     
     
    Let me know if this helps!
    Have a great day! 🙂
     
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!
     

    A4Apollo I am an HP Employee
    A4Apollo le

  • Editing due to not allowed to post photos. Ill desribe as best as I can. they look extremely dull with a blur and grain over the photos. Skin comes out pinkish and other colours come off different then photo. Some have come out with the eyes and outlines looking funny almost cartoonish.  

    Beth941 le

laissez un commentaire

Veuillez noter que les commentaires doivent être approuvés avant d'être publiés