problème avec l'encre de l'imprimante hp envie 4507

Publié par virgio le

Veuillez inspecter votre commande à la réception et nous contacter immédiatement si l'article est défectueux, endommagé ou si vous recevez le mauvais article, afin que nous puissions évaluer le problème et le corriger.Garantie matérielle limitée d'un an ; accès aux services d'assistance de classe mondiale via http://www.support.hp.comet quand j'imprime de diagnostic j'ai la bande noire, bleu et jaune mais la rouge qui est entre la bleu et jaune est vierge est vierge, rien n'est imprimer à ce niveau (voir photo commune).

Utenti che vedono un grande valore nelle foto tangibili e stampano per amare, curare e conservare i ricordi creando bellissimi album e regali fotografici.

Revivez chaque moment amusant avec une application incroyable.IMG_20200814_200611.jpg

Cordialité

← Article plus ancien Message plus récent →

3 commentaires

  • @virgio
     
    Welcome to the HP support community.
     
    Manually clean the area around the ink nozzles

    Gather the following materials:

    Dry foam-rubber swabs, lint-free cloth, or any soft material that does not come apart or leave fibers (coffee filters work well)

    Distilled, filtered, or bottled water (tap water might contain contaminants that can damage the ink cartridges)
       CAUTION: 
    Do not use platen cleaners or alcohol to clean the area. These can damage the ink cartridge or the printer.

    Make sure the printer is on.

    Open the scanner lid.

    Open the ink cartridge access door.
    The carriage moves to the ink cartridge access area.
    Figure : Open the ink cartridge access door

    Wait until the carriage is idle and silent before continuing.

    To release the ink cartridge, lift the lid on the ink cartridge slot, and then gently push the lid back until it stops.

    Pull up on the ink cartridge to remove it from the slot.
    Figure : Remove the ink cartridge

     

    Lift the lid

    Gently push the lid back

    Pull up on the ink cartridge

       CAUTION: 
    Do not remove both ink cartridges at the same time. Remove and clean each ink cartridge one at a time. Do not leave an ink cartridge outside the printer for more than 30 minutes.

    Hold the ink cartridge by its sides.
    Figure : Hold the ink cartridge by its sides

    Inspect the ink cartridge contacts for ink and debris buildup.
       CAUTION: 
    Do not touch the copper-colored contacts or the ink nozzles. Touching these parts can result in clogs, ink failure, and bad electrical connections.

    Figure : Do not touch the contacts or nozzles

    Lightly moisten a clean, foam-rubber swab with distilled water, and then squeeze any excess water from it.

    Clean the face and edges around the ink nozzle with the swab.
       CAUTION: 
    Do not clean the ink nozzle plate.

    Figure : Clean the area around the ink nozzle

     

    Nozzle plate – Do not clean

    Area surrounding ink nozzle – Do clean

    Ink cartridge contacts – Do not clean

    Either let the ink cartridge sit for 10 minutes to allow the cleaned area to dry, or use a new swab to dry it.

    Hold the ink cartridge at a slight upward angle with the ink cartridge contacts facing the rear of the printer, and then slide the ink cartridge into the empty slot.
    Figure : Reinstall the ink cartridge

    Close the lid on the ink cartridge slot to secure the ink cartridge into place.
    Figure : Close the ink cartridge lid

    Repeat these steps to clean the area surrounding the ink nozzle on the other ink cartridge.

    Close the ink cartridge access door.
    Figure : Close the ink cartridge access door

    Close the scanner lid.

    Try printing again.

    You can refer this HP support document for more assistance:- Click here
     
    I hope that helps.
    To thank me for my efforts to help you, please mark my post as an accepted solution so that it benefits several others.
    Cheers.

    Sandytechy20 I am an HP Employee
    sandytechy20 le

  • Hello, I have had a color ink cartridge for several years and today I am installing them in my printer which works fine before and when I want to print anything that makes it be red and green. is it because my cartridge is on standby because i did everything neat, alignment, test and nothing. and when I print the diagnostic I have the black, blue and yellow band but the red which is between the blue and yellow is blank is blank, nothing is printed at this level (see common photo). Could you tell me if it is the cartridge that is quite a few years old but has never been unpacked that is causing this problem or will there be another problem? Looking forward to a response from your party, thank you.

    virgio le

  • Hi there! Thank you for visiting our English HP Support Community! 🙂
     
    We advise you to post your question in English to insure a quick response for the Community. This can also help other users to take advantage of your post, in the case they have the same question.
     
    Or, if you prefer, you can visit the HP Support website (https://support.hp.com/us-en?openCLC=true), to find the support channel for your region.
     
    Thank you for your understanding.
     
    Kind regards,
     
    BiancaS.

    I work on behalf of HP.

    BiancaS le

laissez un commentaire

Veuillez noter que les commentaires doivent être approuvés avant d'être publiés