Diagnostic
There are 0 items in your cart
View all items >Sub-totalbefore tax & fees
$0.00
Mon deuxième pignon 100 et toujours de mauvaise qualité
Publié par CarolCam le
Je suis vraiment mécontent du produit. J'en ai acheté un en décembre et j'ai imprimé quelques photos qui étaient correctes, mais après 6 tirages, il a commencé à montrer des lignes verticales et une teinte magenta. Cela s'est produit lorsque la garantie du magasin a expiré, puis j'ai cherché un service d'assistance à vancouver sur le site Web de HP, je l'ai trouvé et quand j'y suis allé, l'endroit était fermé depuis plus d'un an ! Donc, sans support pour réparer mon Sprocket, je suis allé au magasin que j'avais acheté et heureusement, ils m'en ont donné un autre tout neuf, et devinez quoi ?! Couleur magenta et pas de contraste !! Oui, j'ai fait tout ce que j'ai pu : mettre à jour le firmware, utiliser les papiers officiels et la qualité est toujours mauvaise. Je suis vraiment fatigué et contrarié par le produit qui est censé être un amazone, mais ce n'est pas le cas. Je veux vraiment voir une lumière au bout du tunnel, mais c'est benn dur. Que puis-je faire d'autre? Pour imprimer une, au moins, belle photo ?
← Article plus ancien Message plus récent →
Hi! @CarolCam, Thank you for visiting the HP Forums! A great place where you can find solutions for your issues with help from the community!
I understand you have print quality issues while printing from the sprocket printer.
Don’t worry I’ll try to help you out.
Did you make any changes to your printer?
Please share the image you are running the device to assist you better.
Excellent description and a great diagnosis done. It is greatly appreciated.
Please try few steps recommended below.
1. Reset the Sprocket unit by placing a push-pin or needle into the small hole on the rear of the unit. (Reset instructions in the support doc HERE)
2. Plug in the Sprocket unit with the provided micro-USB cable. Connect to either a computer USB port or USB wall charger.
3. Allow the Sprocket unit to charge for 10 minutes. Note: A call back may be required in these instances.
4. Power on the Sprocket unit by pressing/holding the power button for 3 seconds.
5. A white LED should illuminate on the rear of the unit if the power-up is successful.
6. Remind the customer to charge their Sprocket for an additional 60-90 minutes to enable a full battery charge.
Also, try the steps recommended below.
Turn on the printer. By default, the printer is set to turn off after 5 minutes. To change when the printer automatically
turns off, open the HP Sprocket app on your mobile device. Tap , tap sprocket, and then tap Auto Off. Select when
you want the printer to turn off.
• Restart your mobile device. Turning off and then turning on your mobile device might clear any errors.
• Check for an HP Sprocket app update. On your mobile device, go to the Google Play Store™ or the App Store®, and then
search for the HP Sprocket app. Select the app from the list, and then check for an update.
• Update the printer firmware. On your mobile device, make sure it is connected to the Internet, and then open the HP
Sprocket app. If there is a firmware update available, a firmware update screen displays. Follow the on-screen prompts
to complete the update.
Troubleshooting and FAQs
• Update the software on your mobile device. Check your mobile device settings to confirm you have the latest version
A4Apollo I am an HP Employeeof the operating system software installed. Contact your mobile phone manufacturer for more information about
updating the operating system.
If the issue still persists try updating the sprocket firmware from the sprocket app and check if it helps.
Open Sprocket app go to menu—>Sprocket—→ Printers; A blue firmware update link will be present if an update is available.
Refer this article to further troubleshoot HP sprocket app issues. Click Here
Let me know if this helps!
Have a great day! 🙂
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!